Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

$714.00
Optimize your Zipp wheels with CeramicSpeed Hub Bearings to benefit from reduced friction and increased performance. The result is higher speed with the same effort as well as a higher top speed. CeramicSpeed Wheel Bearings have a proven lifetime, which is 3-5 times longer than standard bearings. All components are optimized for low friction and prolonged lifetime. This wheel kit is compatible with 1st generation non-disc Zipp NSW (before mid-2018). In The Box - 4 x 61803 bearings - 1 x 61903 bearing - 1 x 61804 bearing - 10ml syringe of CeramicSpeed All Round Grease - Sticker sheet
$406.00
This is a set of replacement internals for Alfine SG-S700 11-Speed internally geared hubs, allowing you to reuse your old Alfine shell with brand new internals, making it like a new hub. - 187mm axle width
$390.00
- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed
$344.00
Convert your ISO, ISO B, or ISO Superboost DH rear hub to a Shimano Micro Spline compatible driveshell. The conversion kit is complete with an axle, adjustment clamp, driveshell and all driveshell internals for a plug-and-play swap. Micro Spline Driveshell Instructions - Compatible with Shimano Micro Spline cassettes; XTR, XT, and SLX - Compatible with ISO 142x12mm, ISO B 148x12mm, and ISO Superboost DH 157x12mm rear hubs.
$129.00 - $216.00
Freehub bodies for Zipp Cognition hubs.
$206.00
Zipp Speed Weaponry Rear Axle Conversion Kit - Not to be used on 188 V6 or earlier rear hubs - Only to be used to convert Zipp's 188 V7 10-speed rear hubs to 11-speed
$194.00
Wheel Freehub Kit SRAM XDR for Super 9RB - Compatible only with the Super 9 - Compatible With: WH-SP9-CCR-A1
$9.99 - $153.99
Looking for a super lightweight but badass tubeless sealant? Boom, you've just found it my friend! No Puncture Hassle performs under the most brutal race conditions. The cutting-edge microfiber molecules fill the bigger holes and tears, whilst the advanced latex forms a strong seal instantly. The formula also contains a unique UV detection system that highlights any punctures you haven’t seen during your ride. Developed with the world's top downhillers and pro peloton teams, to give you the finest tire sealant available. It's non-corrosive and easily washes off with water. Compatible with tubeless ready and full UST wheels/tires, No Puncture Hassle works from 15psi-120psi and temperatures from -20°C to +50°C. Our pouch is designed to fit your Presta valve perfectly and is ideal to add to your toolkit or ride pack for emergency top ups on the go! - For Downhill, Enduro and Road tires - Seals tears and holes up to 6mm - Contains UV puncture detection - Won't dry out or ball - Works from 15psi-120psi and temperatures from -20°C to +50°C - Biodegradable
$151.00
This 11-speed freehub is only compatible with model-year 2013 (V8) and 2014 (V9) Zipp wheelsets. Check that your hub has a black end cap before using this freehub. Use the spacer for compatibility with 10-speed Shimano and SRAM drivetrains after installation. The red freehub is designed for SRAM or Shimano drivetrains and includes a spacer for 10-speed compatibility. The blue freehub is designed for Campagnolo drivetrains. The Campagnolo version requires one 0.25mm axle washer, which is included. - 10 to 11-speed wheel conversion can only be completed by an authorized Zipp Service Center - Not intended to convert older 10-speed freehub wheels to 11-speed freehub wheels - Only intended to swap freehub compatibility (SRAM/Shimano - Campagnolo) with current 11-speed wheels - Includes cassette spacer - Material: Aluminum
$150.00
CushCore is an engineered foam insert to be mounted inside a tire, designed to absorb impacts, reduce vibration, and increase lateral stability. These characteristics translate to a more controlled, comfortable, and faster ride. - The system is designed to be used with tubeless-ready or tubeless converted rims and tires and is compatible with tubeless tire sealants - A specially designed tubeless air valve is included with each insert; allowing air to move through the valve without becoming obstructed by the insert - The insert divides the inner volume of the tire in half, maintaining air underneath the tread and the foam insert next to the rim - Fits tire widths 2.1 – 2.6" and rims with internal width 22 – 35mm Includes: - 2 CushCore Inserts - 2 CushCore Tubeless Air Valves - 4 Rim Stickers - Installation Instructions
$11.50 - $140.00
We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels
$129.99
Replacement Alloy XDR (XD-Road) Freehub Body, for all HEX Rear Hubs. Includes spacer ring to also allow the use of MTB cassettes. Compatible with: - All HEX J-Type, Straightpull, and Gravel rear wheels Not compatible with: - SPIKE/OOZY/SPOON hubs
$129.99
Replacement Freehub body for OOZY Trail R142/135, SPIKE R135/142, or SPIKE DH R150/157 Rear hubs. Compatible with all OOZY hubs and wheels. Compatible only with SPIKE and SPOON wheels (135mm and 150mm) produced in 2016 or later (with SPIKE hubs).
$115.50
125 piece assortment of precision machined axle spacers (0.5mm to 5mm thickness). - Outside Diameter of Spacers: 16mm - Inside Diameter of Spacers: 10mm Kit includes: - (10) - 0.5mm thick spacers - (30) - 1mm thick spacers - (30) - 2mm thick spacers - (25) - 3mm thick spacers - (15) - 4mm thick spacers - (15) - 5mm thick spacers
$108.00
- Freehub for Cognition V2 hubs
$108.00
Wheel Freehub Kit—(Includes Bearings & Pawls) 11/12 Speed XD—X0 HUBS/RISE 60 (B1)/ROAM 30/ROAM 40/RAIL 40/RISE XX/ROAM 50/60 (B1) Compatible With: HU-X0-A1, WH-RAIL-40-A1, WH-RISE-60-B1, WH-RISE-XX-A1, WH-ROAM-30-A1, WH-ROAM-40-A1, WH-ROAM-50-A1, WH-ROAM-50-B1, WH-ROAM-60-B1
$108.00
Wheel Freehub Kit SS 176/177 SRAM XDR - End Caps Not Included Compatible With: WH-202-CCR-A1, WH-202-TLD-A1, WH-202-TUD-A1, WH-302-CCD-A1, WH-302-CCR-A1, WH-302-TLR-A1, WH-303-CCR-B1, WH-303-TLD-A1, WH-303-TUD-B1, WH-303-TUR-B1, WH-30C-CLD-A1, WH-30C-CLR-A1, WH-404-CCR-A1, WH-404-CCR-B1, WH-404-TLD-A1, WH-808-CCR-B1, WH-808-TLD-A1, WH-SP9-CC30-A1, WH-SP9-CCD-A1, WH-SP9-CCR-A1, WH-SP9-TUD-A1
$100.00
- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body
$100.00
- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body
$100.00
- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body
$99.99
Replacement freehub bodies for Easton X5 hubs. - Material: Aluminum - Cassette Body Type: Shimano/SRAM 8, 9, 10 Speed , Shimano Dynasys 11 Speed Mountain
$99.99
Replacement freehub bodies for Easton X5 hubs. - Material: Aluminum - Cassette Body Type: SRAM XD 11/12 Speed
$81.80 - $99.60
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included
$54.00 - $98.00
Match your Beyond Black hubs, spokes and decals (each sold separately) with skewers from Zipp. - Sold in pairs - Stainless steel: 85 grams/set - Titanium: 78 grams/set
$95.50
Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs.
$95.00
Replacement Freehub Body for Trace hubs.
$95.00
Replacement freehub bodies for Vault hubs. - Use to replace worn/damaged freehub body or to switch cassette standards. - 60T
$92.40
DT Swiss tubeless ready tape seals the rim for tubeless applications and also works well as rim tape for tube-type set ups. - Highly resistant adhesive tape works as a rim tape and airseal
$80.90
Maximum stiffness and highest safety—the RWS Quick Release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. The perfect choice for anyone who is looking for maximum performance and safety.
$80.90
Maximum stiffness and highest safety—the RWS Quick Release for road and MTB. Our patented RWS axle system is stiffer, safer, and easier to use than conventional quick-release axles. The RWS quick release is absolutely reliable and offers a strong connection to the frame. The perfect choice for anyone who is looking for maximum performance and safety.
Page 1 of 9 Next page